This function enables this unit to automatically tune in to FM stations that have a strong signal and store up to 40 of those stations in order. You can then easily recall any preset station by selecting its preset number. See pages 18 and 19 for tuning instructions. Page Clearing All Preset Stations Clearing all preset stations Follow the steps below to clear all preset stations. When the ninth device is paired, the pairing settings for the device which has not been used for the longest period of time will be deleted.
Operate the Bluetooth component for playback. Also, you can view the signal information for certain input sources. The procedure for setting the Option menu items is described below.
Page Troubleshooting Refer to the chart below if this unit does not function properly. If the problem you are experiencing is not listed below or if the instructions below do not help, turn off this unit, disconnect the power cable, and contact the nearest authorized Yamaha dealer or service center. Page 37 Problem Incorrect cable connections. No connection from the turntable to the GND terminal.
The record is being played on a turntable The volume level is with an MC cartridge. There is multipath interference. There is distortion, and clear reception Place the YID-W10 receiver as far away from this unit as possible. Cause Turn on this unit or set it to standby mode. The Bluetooth Wireless Audio Receiver and the Bluetooth component are in the process of establishing a connection. This manual is also suitable for: R-sbl.
With these connections, the mid and high frequency drivers are connected to one set of terminals and the low frequency driver to another set of terminals. When making bi-wire connections, remove the shorting bridges or cables on the speaker. Banana plug.
Indoor antennas for receiving FM and AM broadcasts are included with this unit. In general, these antennas should provide sufficient signal strength. Connect each antenna correctly to the designated terminals. If you experience poor reception quality, install an outdoor antenna. Consult the nearest authorized Yamaha dealer or service center about outdoor antennas. For maximum safety and minimum interference, connect the antenna GND terminal to a good earth ground.
A good earth ground is a metal stake driven into moist earth. These jacks are used to connect a signal-processing system such as a graphic equalizer or a surround-sound processor to this unit. If an external unit is connected to these jacks, the VOLUME control of this unit can be used to adjust the overall sound output level. Plug the power cable into the AC wall outlet after all other connections are complete.
If removed, no sound will be output from this unit. Leaving the power cable connected could cause noise to be emitted from the speakers or damage the unit. Use the controls on the external control amplifier to make volume adjustments, etc. Generates a normal phase and reverse phase signal for both the left and right channels from the input signal and uses the four electronic volumes to send a balanced signal to the amplifying circuit.
This feature provides clearer sound as a result of:. Routes input signals from your CD player directly to the specially built-in amplifier for the CD player. When you feel there is not enough bass low frequency sound , rotate clockwise to boost. When you feel there is too much bass, rotate counterclockwise to suppress.
When you feel there is not enough treble high frequency sound , rotate clockwise to boost. When you feel there is too much treble, rotate counterclockwise to suppress. The BALANCE control adjusts the sound output balance of the left and right speakers to compensate for sound imbalance caused by speaker locations or listening room conditions.
Welcome to ManualMachine. We have sent a verification link to to complete your registration. Log In Sign Up. Forgot password? Enter your email address and check your inbox. Please check your email for further instructions. Enter a new password. Follow all installation instructions. If the antenna lead-in is ohm ribbon lead, change the lead-in to coaxial type cable.
Compliance with these If these corrective measures do not produce requirements provides a reasonable level of assurance that satisfactory results, please contact the local retailer your use of this product in a residential environment will authorized to distribute this type of product.
If you can not result in harmful interference with other electronic not locate the appropriate retailer, please contact devices. Yamaha Electronics Corp. Note In standby mode, this unit consumes a small amount of power to receive infrared signals from the remote control. B Remote control sensor Receives infrared signals from the remote control.
Note Zone 2 cannot be used while this function is turned on. K BALANCE control Adjusts the sound output balance of the left and right speakers to compensate for sound imbalances caused by speaker locations or listening room conditions see page Note This does not affect the output level of the REC jacks.
B P indicator Lights up when a preset number is selected. C Multi-information display Shows information when adjusting or changing settings. D Volume indicator. Blinks while the automatic station preset feature is scanning for FM stations to register as presets. Note Do not connect a component that requires more than mA of electric current, otherwise the component may not perform consistently or properly due to insufficient power.
Insulation sheet Note The Zone 2 remote control comes with a battery already installed. Straight pin CR battery. Approximately 6 m 20 ft Remote control or Zone 2 remote control. For information about Speakers A other components that can be connected to this unit, see page Note When inserting speaker cables into the speaker terminals, insert only the bare speaker wire.
Note When making bi-wire connections, remove the shorting bridges or cables on the speaker. Note If you experience poor reception quality, install an outdoor antenna. Outdoor AM antenna Use 5 to 10 m of vinylcovered wire extended outdoors from a window. Jumper pins. Power cable R-S only. The center position produces a flat response. BASS When you feel there is not enough bass low frequency sound , rotate clockwise to boost. You can only view or download manuals with. Sign Up and get 5 for free.
Upload your files to the site. You get 1 for each file you add. Get 1 for every time someone downloads your manual. Buy as many as you need. This may shorten the life of the new batteries or cause old batteries to leak.
Batteries that look the same may have a different specification. Turns on and off the power of this unit see page On position: Pushed inward. This unit consumes a small amount of power even when turned off or when in standby mode. Changes the brightness level of the front panel display. Choose brightness from 3 levels by pressing this button repeatedly. Allows you to listen to a source in the purest possible sound see page The indicator above it lights up and the front panel display turns off when this function is turned on.
Increases or decreases the low frequency response. The center position produces a flat response see page Increases or decreases the high frequency response.
Adjusts the sound output balance of the left and right speakers to compensate for sound imbalances caused by speaker locations or listening room conditions see page Light up according to the set of speakers selected.
Both indicators light up when both sets of speakers are selected. Lights up when you recall a preset radio station. Blinks while the automatic station preset feature is scanning for FM stations to register as presets. Lights up when this unit is receiving a strong signal for an FM stereo broadcast. Lights up when a preset number is selected. Blinks while you are registering a preset radio station.
Used to enable or disable the automatic power down function. When this function is enabled, this unit automatically enters standby mode if it is not operated for a certain amount of time 3 settings are available; see page This section describes the function of each button on the remote control used to control this unit or a Yamaha CD player. This button functions only when the A power button on the front panel is in the on position.
Mutes the sound output. Press again to restore the sound output to the previous volume level. Returns to the previous menu or ends the menu display when using the Option menu see page For more information, see page The following buttons can be used to control a Yamaha CD player when CD is selected as the input source.
Even when using a Yamaha CD player, certain components and features may not be available. The remote control transmits a directional infrared beam. Be sure to aim the remote control directly at the remote control sensor on the front panel of this unit during operation. Welcome to ManualMachine. We have sent a verification link to to complete your registration. Log In Sign Up. Forgot password?
Enter your email address and check your inbox. Please check your email for further instructions. Enter a new password.
0コメント